Shear Performance of Fiber-Reinforced Cementitious Composites Beam-Column Joint Using Various Fibers

Faizal Hanif(1*), Toshiyuki Kanakubo(2)

(1) Universitas Gadjah Mada
(2) Engineering Mechanics and Energy, University of Tsukuba, Tsukuba
(*) Corresponding Author


Increasing demands of reinforcement in the joint panel are now requiring more effective system to reduce the complicated fabrication by widely used precast system. The joint panel is responsible to keep the load transfer through beam and column as a crucial part in a structural frame that ensures the main feature of the whole structure during earthquake. Since precast system might reduce the joint panel monolithic integrity and stiffness, an innovation by adding fiber into the grouting system will give a breakthrough. The loading test of precast concrete beam-column joints using FRCC (Fiber-Reinforced Cementitious Composites) in joint panel was conducted to evaluate the influences of fiber towards shear performance. The experimental factor is fiber types with same volume fraction in mortar matrix of joint panel. Two specimens with Aramid-fiber and PP-fiber by two percent of volume fraction are designed to fail by shear failure in joint panel by reversed cyclic testing method. The comparison amongst those experiment results by various parameters for the shear performance of FRCC beam-column joints using various fibers are discussed. Preceding specimens was using no fiber, PVA fiber, and steel fiber has been carried out. Through the current experimental results and the comparison with previous experiment results, it can be recognized that by using fibers in joint panel was observed qualitatively could prevent crack widening with equitable and smaller crack width, improved the shear capacity by widening the hysteretic area, increased maximum load in positive loading and negative loading, and decreased the deformation rate. Elastic modulus properties of fiber are observed to give the most impact towards shear performance.


Joint panel, fiber, FRCC, elastic modulus, shear performance

Full Text:



ACI Committee, 2001. State of the Art Report on Fiber Reinforced Concrete. American Concrete Institute.

American Iron and Steel Institute, 2007. Monotonic and Cyclic Tests of Long Steel-Frame Shear Walls with Openings, Blacksburg: Steel Framing Alliance.

Ando, M. et al., 2016. Study on Shear Capacity of DFRCC Beam-Column Joints. Summaries of Technical Papers of Annual Meeting of AIJ, Volume IV, pp. 411-414.

Architectural Institute of Japan, 1999. Design Guidelines for Earthquake Resistant Reinforced Concrete Buildings Based on Inelastic Displacement Concept, s.l.: Architectural Institute of Japan.

ASTM International, 2002. Standard Test Methods for Cyclic (Reversed) Load Test for Shear Resistance of Walls for Buildings, Pennsylvania: American Section of the International Association for Testing Materials.

Bentur , A. & Mindess, S., 2007. Fibre Reinforced Cementitious Composites. Taylor & Francis.

Guner, S., 2016. Completed Projects - Nonlinear Analysis of Concrete Structures. [Online]
Available at:
[Accessed 8 November 2016].

Hanif, F., 2017. Shear Performance Of Fiber Cementitious Composites Beam-column Joint Using Various Fibers, Yogyakarta: Undergraduate Thesis. Faculty of Engineering, Universitas Gadjah Mada.

Kanakubo, T., 2006. Tensile Characteristics Evaluation Method for Ductile Fiber-Reinforced Cementitious Composites. Journal of Advanced Concrete Technology, 4(1), pp. 3-17.

Kanakubo, T., Shimizu, K., Kanda, T. & Nagai, S., 2007. Evaluation of Bending and Shear Capacities of HPFRCC Members Toward The Structural Application, Sapparo: Hokkaido University COE Workshop on HPFRCC for Sustainable Infrastructure System.

Kanakubo, T., Shimizu, K., Kanda, T. & Nagai, S., 2010. Shear Transmission on Crack Surface of ECC Fracture Mechanics of Concrete and Concrete Structures - High Performance, Fiber Reinforced Concrete, Special Loadings and Structural Applications, Sapparo: Hokkaido University COE Workshop on HPFRCC for Sustainable Infrastructure System.

Patah, D., Saputra, A. & Triwiyono, A., 2016. Retrofitting on Flexural Strength of RC Columns using Polyester Resin Concrete. Journal of the Civil Engineering Forum, 2(1), pp. 123-130. doi:10.22146/jcef.24305

Sano, N. et al., 2015. Structural Performances of Beam-Column Joint Using DFRCC. Victoria, Canadian Association for Earthquake Engineering.

Sano, N., Yasojima, A., Kanakubo, T. & Hasoya, H., 2016. Structural Performances of Precast Concrete Beam-Column Joints Using DFRCC in Panel. AIJ Journal of Technology and Design, 22(50), pp. 109-114.

Shimizu, K., Kanakubo, T., Kanda, T. & Nagai, S., 2004. Shear Behavior of Steel Reinforced PVA-ECC Beams. Vancouver, 13th World Conference on Earthquake Engineering.

Shiohara, H., 2001. New Model for Shear Failure of RC Interior Beam-Column Connections. Journal of Structural Engineering.

Yamada, H., Yasojima, A., Sano, N. & Kanakubo, T., 2016. Influence of Fiber Type on Shear Capacity of PCa Beam-Column Joint Using DFRCC. s.l., Proceedings of The Japan Concrete Institute, pp. 1327-1332.


Article Metrics

Abstract views : 2498 | views : 2901


  • There are currently no refbacks.

Copyright (c) 2022 The Author(s)

The content of this website is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
ISSN 5249-5925 (online) | ISSN 2581-1037 (print)
Jl. Grafika No.2 Kampus UGM, Yogyakarta 55281
Email :
Web Analytics JCEF Stats