Mechanical Properties and Corrosion Characteristics of Dissimilar Friction Stir Welded AA1000/AA6061-T6 Aluminum Alloys

https://doi.org/10.22146/jmdt.74006

Chhorn Sokvisal(1), Mochammad Noer Ilman(2*)

(1) Departemen Teknik Mesin dan Industri, Fakultas Teknik, Universitas Gadjah Mada. Jl. Grafika No. 2, Kompleks UGM, Yogyakarta 55281, Indonesia
(2) Departemen Teknik Mesin dan Industri, Fakultas Teknik, Universitas Gadjah Mada
(*) Corresponding Author

Abstract


This paper is aimed to investigate microstructure, corrosion and mechanical properties of dissimilar metal weld joints between AA1000 and AA6061-T6 under different tool rotational speeds of 910, 1500, and 2280 rpm at a constant transverse speed of 30 mm/min. Several experimental works have been conducted including microstructure observation using optical microscopy and Scanning Electron Microscopy (SEM) equipped with Energy Dispersive X-ray Spectroscopy (EDS), Vickers microhardness measurements, tensile tests, and corrosion measurements using Potentiodynamic Polarization method. Results show that increasing tool rotational speed from 910 rpm to 1500 rpm increases the degree of homogeneity in nugget zone and improves strength of the weld joint but further increase in the tool rotational speed up to 2280 rpm degrades the mechanical properties due to coarsening of the microstructure. Furthermore, corrosion rate of the nugget zone (NZ) is in between the two base metals.


Keywords


Aluminum alloys; Friction Stir Welding; Dissimilar metals; Strengths; Corrosion.

Full Text:

PDF


References

A. Kumar, S. K. Sharma, K. Pal, and S. Mula, “Effect of Process Parameters on Microstructural Evolution , Mechanical Properties and Corrosion Behavior of Friction Stir Processed Al 7075 Alloy,” J. Mater. Eng. Perform., vol. 26, no. 3, pp. 1122–1134, 2017.

A. Rudolf, Extrusion of semifinished products in aluminum alloys. 2006.

C. Shen, J. Zhang, and J. Ge, “Microstructures and electrochemical behaviors of the friction stir welding dissimilar weld,” J. Environ. Sci., vol. 23, no. SUPPL., pp. S32–S35, 2011.

C. Zhang, G. Huang, Y. Cao, Y. Zhu, and Q. Liu, “On the microstructure and mechanical properties of similar and dissimilar AA7075 and AA2024 friction stir welding joints: Effect of rotational speed,” J. Manuf. Process., vol. 37, no. December 2018, pp. 470–487, 2019.

D. Devaiah, D. K. Kishore, and D. P. Laxminarayana, “Effect of Material Location and Tool Rotational Speed on the Mechanical Properties of Dissimilar Friction Stir Welded Aluminum Alloys (5083-H321to 6061-T6),” Bonfring Int. J. Ind. Eng. Manag. Sci., vol. 6, no. 4, pp. 186–190, 2016.

H. Jamshidi Aval, S. Serajzadeh, N. A. Sakharova, A. H. Kokabi, and A. Loureiro, “A study on microstructures and residual stress distributions in dissimilar friction-stir welding of AA5086-AA6061,” J. Mater. Sci., vol. 47, no. 14, pp. 5428–5437, 2012.

H. Mishra, R. and Sidhar, Friction Stir Welding of 2XXX Aluminum Alloys Including Al À Li Alloys Friction Stir Welding of 2XXX Aluminum Alloys Including Al À Li Alloys A Volume in the Friction Stir Welding and Processing Book Series. 2016.

J. R. Davis, “Aluminum and Aluminum Alloys,” in Light Metals and Alloys, ASM International, 2001, pp. 351–416.

J. Yan, M. A. Sutton, and A. P. Reynolds, “Process-structure-property relationships for nugget and heat affected zone regions of AA2524-T351 friction stir welds,” Sci. Technol. Weld. Join., vol. 10, no. 6, pp. 725–736, 2005.

M. M. Moradi, H. Jamshidi Aval, R. Jamaati, S. Amirkhanlou, and S. Ji, “Microstructure and texture evolution of friction stir welded dissimilar aluminum alloys: AA2024 and AA6061,” J. Manuf. Process., vol. 32, pp. 1–10, 2018.

M. P. Hossein Karami Pabandi, Hamid Reza Jashnan, “Effect of precipitation hardening heat treatment on mechanical and microstructure features of dissimilar friction stir welded AA2024-T6 and AA6061-T6 alloys,” 2017.

P. Mukhopadhyay, “Alloy Designation, Processing, and Use of AA6XXX Series Aluminium Alloys,” ISRN Metall., vol. 2012, no. Table 1, pp. 1–15, 2012.

P. Sadeesh et al., “Studies on friction stir welding of aa 2024 and aa 6061 dissimilar metals,” Procedia Eng., vol. 75, pp. 145–149, 2014.

R. I. Rodriguez, J. B. Jordon, P. G. Allison, T. Rushing, and L. Garcia, “Microstructure and mechanical properties of dissimilar friction stir welding of 6061-to-7050 aluminum alloys,” Mater. Des., vol. 83, pp. 60–65, 2015.

T. A. Association, “Rolling Aluminum : From the Mine Through the Mill on the Sheet and Plate Division ’ s Technology Committee,” p. 135, 1990.

W. B. Lee, Y. M. Yeon, and S. B. Jung, “The mechanical properties related to the dominant microstructure in the weld zone of dissimilar formed Al alloy joints by friction stir welding,” J. Mater. Sci., vol. 38, no. 20, pp. 4183–4191, 2003.

W. M. Thomas;, N. J. C., and Needham, “Friction Stir Butt Welding,” 1991.



DOI: https://doi.org/10.22146/jmdt.74006

Article Metrics

Abstract views : 278 | views : 246

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.