Predicting of Parameters Affecting on PE Wax Powder Size Distribution and Shape in Atomization Process

  • Ubonwan Madua Department of Chemical Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai, Songkhla 90112
  • Kulchanat Prasertsit Department of Chemical Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai, Songkhla 90112
  • Paiboon Innachitra Department of Chemical Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai, Songkhla 90112
  • Tanakorn Keatkhunboot Department of Chemical Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai, Songkhla 90112
Keywords: Spray drying, Atomization process, Polymer powder, atomizer, gas atomization, powder size distribution analysis

Abstract

The aim of this work is to study the parameters affecting on the particle size distribution and shape of Polyethylene wax (PE wax) powders in atomization process. Effect of liquid flow rate, melting temperature and air pressure are studied parameters. External mixing two fluid nozzles is used and temperature is controlled at 200˚C to avoid freeze-up within the liquid cap. PE wax is melted at various temperatures from 120˚C to 180˚C and is atomized with air pressures from 1 to 7 bar. Particle size and size distribution are determined by Particle Sizing Unified System (Mastersizer, 2000). Using 1 bar of air pressure, 140˚C of melting temperature and 3.0:1.5 of ALR gives the PE wax powders size that smaller than 200 micron and high bulk density. Moreover, smoothly and silky surface of PE wax powders are obtained.

References

1. Otaigbe, J.U. and J.M. McAvoy. (1998).Gas atomization of polymers. I. Feasibility studies and process development. Advances in Polymer Technology, 17(2): p. 145-160.
2. Wiwax. LTD. (2011). PE wax applications. Available from: http://www/wiwax.eu/en/main.php?k0 =APPLICATIONS. Accessed June 2011.
3. Sh-jiyuan Ltd. (2011). Spray drying manual. Avairable from: http://www.sh- jiyuan.com/download/01/SDX_MANUA L.PDF. Accessed June 2011.
4. Ejim, C.E., Rahman, M.A., Amirfazli, A. and Bleck, B.A.( 2010). Effects of liquid viscosity and surface tension on atomization in two-phase, gas/liquid fluid coker nozzles. Fuel. 89(8): p. 1872- 1882.
Published
2013-12-31
How to Cite
Madua, U., Prasertsit, K., Innachitra, P., & Keatkhunboot, T. (2013). Predicting of Parameters Affecting on PE Wax Powder Size Distribution and Shape in Atomization Process. ASEAN Journal of Chemical Engineering, 13(2), 1-8. Retrieved from https://journal.ugm.ac.id/v3/AJChE/article/view/8148
Issue
Vol 13 No 2 (2013)
Section
Articles

Copyright holder for articles is ASEAN Journal of Chemical Engineering. Articles published in ASEAN J. Chem. Eng. are distributed under a Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) license. 

Authors agree to transfer all copyright rights in and to the above work to the ASEAN Journal of Chemical Engineering Editorial Board so that the Editorial Board shall have the right to publish the work for non-profit use in any media or form. In return, authors retain: (1) all proprietary rights other than copyright; (2) re-use of all or part of the above paper in their other work; (3) right to reproduce or authorize others to reproduce the above paper for authors’ personal use or for company use if the source and the journal copyright notice is indicated, and if the reproduction is not made for the purpose of sale.