Improvement of Andong Horseshoe Quality in Yogyakarta City to Support City Tourism

https://doi.org/10.22146/jpkm.44045

Alva Edy Tontowi(1*), Mochammad Noer Ilman(2), Dawi Karomati Baroroh(3)

(1) Department of Mechanical and Industrial Engineering, Faculty of Engineering, Universitas Gadjah Mada
(2) Department of Mechanical and Industrial Engineering, Faculty of Engineering, Universitas Gadjah Mada
(3) Department of Mechanical and Industrial Engineering, Faculty of Engineering, Universitas Gadjah Mada
(*) Corresponding Author

Abstract


The Zero Kilometer Point is an important route for andong horses in Yogyakarta City. The renovation and replacement of road material with andesite can cause horses to slip because the horseshoes have not been adjusted to the new road material. If neglected, it can harm the horses and its owners, reducing the tourism industry in Yogyakarta. On the other hand, horseshoes demand is still met by small and medium enterprises (SME) without a well-standardized system. After doing technical testing to the existing horseshoe design, several alternative solutions were obtained for horseshoe redesign (1) by adding rubber pads and (2) serrated without rubber pads. Based on analysis and testing, it was found that horseshoe with the addition of rubber by 40% was able to increase the friction value to 0.54 or 10% from the initial condition. Besides improving the productivity and quality of SME horseshoe products, several solutions should be considered, including (1) change the layout design of SME by implementing 5S lean six sigma principles and (2) apply new methods/technology to maintain the standardization of horseshoe product. Implementation of both solutions will guarantee not only the quality product but also SME production. It is hoped that all the improvements that have been made will increase the quantity and quality of horseshoe products. Then it will also be able to improve the image of Yogyakarta City as a tourist city.


Keywords


Horseshoe; Small Medium Enterprise (SME); Yogyakarta; Redesign Layout

Full Text:

PDF


References

Agrahari, R.S., Dangle, P.A., Chandratre, K.V. (2015). Implementation Of 5S Methodology In The Small Scale Industry: A Case Study. International Journal Of Scientific & Technology Research, 4(4), 180-187.

BOC. (2016, February 10). Principles Carburising and Carboniting. URL: https://www. Boconline.co.uk/internet.lg.lg.gbr/en/images/Principles%20of%20Carburising%20and%20Carbonitriding410_114378.pdf.

krjogja.com. (2016, January 5). Kunjungan Wisatawan 2014 Lampaui Target. URL: http://krjogja.com/read/247646/kunjungan-wisatawan-2014-lampaui-target.kr.

Kwietniewski, C.E.F., Tetrardini, E., dan Totten, G.E. (2013). Carburizing and Carboniting. Encyclopedia of Tribology, 298-306.

Martin, L.A. (2014). Alternative Materials for the Horseshoe. University of Skövde, Swedia.

Schneider, M. J., dan Chatterjee, M. S. (2015). Introduction to Surface Hardening of Steels. ASM Handbook, 4A.

Solopos.com. (2016, January 5). Diduga Karena Jalan Licin, 2 Kuda Penarik Andong Terpeleset Di Titik Nol Kilometer. URL: https://www.solopos.com/diduga-karena-jalan-licin-2-kuda-penarik-andong-terpeleset-di-titik-nol-kilometer-674007.

Wardhana, R. (2013). Pengaruh Lingkungan Kerja Terhadap Produktifitas Pekerja (Studi Kasus: Industri Kerajinan Gerabah Kasongan Bantul). Universitas Gadjah Mada, Yogyakarta.



DOI: https://doi.org/10.22146/jpkm.44045

Article Metrics

Abstract views : 1611 | views : 1641

Refbacks

  • There are currently no refbacks.




Copyright (c) 2021 Jurnal Pengabdian kepada Masyarakat (Indonesian Journal of Community Engagement)

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Jurnal Pengabdian kepada Masyarakat (Indonesian Journal of Community Engagement)

ISSN (print) 2460-9447ISSN (online) 2541-5883